2017 FRONT AND REAR Use new nut.

of the common nuts and bolts that you'll encounter on a classic VW. And obviously, you should pull the axle fully into the hub, and snug up the nut (or bolt) before starting the torque sequence.

Check the style nut that is on the vehicle when staking the nut. 2012-2015 199/270-ft/lbs/Nm Use new nut. Use new original equipment nut. Style 2 nut has the thick collar (2.7 mm) thickness. Stake new nut. Stake new nut. Turn adjusting nut to align. For Style 1, 244 ft-lbs/330 Nm. So you have to refer to the factory legends to learn the identification symbols and then refer back to circuit diagrams to find the splice and ground locations. Always use a new nut. Tang on ring must press through slot on spindle. Endplay should be .001- .010″.

Back off 45 degrees and retighten to 184 ft-lbs/250 Nm. Tighten to 111 ft-lbs/150 Nm.

One of the most common mistakes people make when installing a new hub assembly is improperly torquing the axle nut.

AWD 2007-2016 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm.

AWD 2015-2017 FRONT 37/50-ft/lbs/Nm [After tightening to specification, turn an additional 60°. Stake style one nut and make sure not to fracture the nut.

2014-2017 Tighten to 258 ft-lbs/350 Nm. 4WD 1980-1991 With manual locking hubs: Tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub. Back off and retighten to 35 ft-lbs/47 Nm. After installation, stake nut. 2015-2017 192/260-ft/lbs/Nm Use new original equipment nut.

When you’re removing the wheel hub nut, you can use an impact wrench to speed up the job. Transcript: One of the most common mistakes people make when installing a new hub assembly is improperly torquing the axle nut. This video will show you where to find the proper torque specs for a Timken hub assembly.

After installation, stake nut.

They include wiring diagrams and technical service bulletins. Back off and retighten to 50 ft-lbs/68 Nm.

Back off 3/ 8 turn. Limited AWD 2017 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm. 2012-2013 Tighten to 111 ft-lbs/150 Nm. Air Cooled VW Engine Torque specifications. Hole in pin must align with locknut. Caprice. Proper torque is critical for two reasons. AWD 2005-2008 118/160-ft/lbs/Nm 192/260-ft/lbs/Nm, AWD 2002-2005 118/160-ft/lbs/Nm 192/260-ft/lbs/Nm.

Style 1 nut has the thin collar (1.5 mm) thickness.

If you need to dig into your doors, dash or console, Alldatadiy.com is the better choice because Eautorepair.net doesn’t any interior or exterior trim or body part removal. 2017 Use new nut. FWD 2012-2015 FRONT 151/205-ft/lbs/Nm Use new original equipment nut. Use new nut. For Style 2, First Pass: 37 ft-lbs/50 Nm; Final Pass: plus 60°. 2011-2017 Tighten in three steps: First, 111 ft-lbs/150 Nm; second, loosen 45 degrees; last, tighten 185 ft-lbs/250 Nm.

Follow these dos and dont’s of wheel bearing torquing to ensure proper installation, repair and happy customers. This video will show you where to find the proper torque specs for a Timken hub assembly. Chevrolet Spark Axle Nut Torque 2013-2015 177/240-ft/lbs/Nm Use new original equipment nut. Well we've gotcha covered! Tighten to 111 ft-lbs/150 Nm. Over 6,000 Automotive Torque Specs. With automatic locking hubs tighten adjusting nut to 50 ft-lbs/68 Nm while turning hub.

Malibu Limited 2016 Tighten to 111 ft-lbs/150 Nm. I believe the spec for the 4 bolts for the stub axle is 44 ft-lbs but what is the axle nut spec? TIA, Tom Loosen 45° then retighten to 199 ft-lbs/270 Nm.

VW Rabbit 2006-09 Front VW Tiguan 2009-13 Front Note A * Please refer to service manual if your application is not listed Vehicles with Hex bolt: Tighten bolt to 148 Lb.

Volkswagen Passat Torque Specs. Impala Limited 2014-2016 155/210-ft/lbs/Nm. 1999 Jetta new body style 2.0L I'm replacing the stub axle and bearing assembly.

This table shows the correct factory recommended tightening torque specifications for most of the common nuts and bolts that you'll encounter on a classic VW.

Pricing: ---Eautorepair.net--- 1 month subscription $19.95 per vehicle 1-year subscription $29.95 per vehicle 4-year subscription $44.95 per vehicle ---Alldatadiy.com--- 1-year $29.95 subscription: additional vehicles $19/95 each 5-year $49.95 subscription: additional vehicles $34.95 each Which one should YOU choose? 2016-2017 185/250-ft/lbs/Nm se new nut. Hole in pin must align with locknut.

SS 2014-2017 Tighten to 258 ft-lbs/350 Nm. Install ring and tighten locknut to 160 ft-lbs/217 Nm minimum.

AWD 2010-2017 FRONT 151/205-ft/lbs/Nm REAR 151/205-ft/lbs/Nm, AWD .2009-2017 FRONT 173/235-ft/lbs/Nm REAR 151/205-ft/lbs/Nm. This table shows the correct factory recommended tightening torque specifications for most

and use the torque values listed below to set those bolts to the correct tightness. Eautorepair.net redraws factory wiring diagrams in color and includes the component, splice and ground locations right in their diagrams.