You are using a standard latex paint on a door that was previously painted with an oil-based paint. You are using Benjamin Moore Advance paint over a previously painted door – this paint can be used over either latex or oil-based paint and is awesome for not leaving roller or brush marks so it’s my go-to paint for trim and doors. Remove the door from its hinge pins with the hammer and place it on the sawhorses.

The process is not difficult, but it can be tedious. If you’re painting your door white and have white trim around it, I recommend using the same paint color and finish as the trim.

Then paint the three vertical strips down the center with the 4″ roller.

Sandpaper  – I use 150 grit and 220 grit, Canvas or plastic drop cloth to protect your floor (I use {these} that you can wash and reuse), Roll of painter’s tape such as {this one}, Paintbrush – {this 2″ angled brush} is my favorite – it works with both oil and latex paints, 4″ woven rollers with 1/4″ nap such as {these rollers} or 4″ foam rollers such as {these rollers} – both work well, Roller handle for 4″ rollers such as {this one}. I like to use a 1 1/2″ brush to paint the recessed molding areas followed by a 4″ roller for the flat surfaces in the middle.

If in case the door is previously painted or stained, then it is advisable to follow up the same pattern to apply a bonding primer on the door before painting. Penny.

Some of my favorite whites for trimwork and doors are Benjamin Moore’s Cloud White and Dove White in either semi-gloss or satin. Any ideas on how to fix? Go top to bottom, use dry brush to get in panels, use a good primer.

You will need to prime if: Priming is ideally done in the same order (edges first, etc. It’s best to paint … Remove the hardware from the door and place it somewhere safe. Make sure to feather the edges of the molding you’re brushing – you don’t want any hard edges.

Kevin hears about preserving historic details while updating the interior space and creating a new garage and master suite. To minimize stroke marks, use long strokes and light pressure on the roller. Pour the paint into a tray.

The last two houses we’ve lived in have been older homes with doors that were yellowed and not in great shape so as I make over each space, I also paint the doors. Use a cloth to remove most of the sanding dust and then go back over the entire door with a tack cloth to get the rest of it. The success of any paint job always starts with good prep work.

For the door hinges, I use a utility knife to gently trace the outside of the hinge, cutting the tape as I go: If you’re repainting an older door, the first step is to fill in any gouges or imperfections with wood filler and sand those areas until smooth (I use 150 grit for this) and then lightly sand the entire door with fine grit (220) sandpaper. How do you know if your door was previously painted with oil-based or latex paint? I’ve never polyurethaned over paint on a door but you could if you make sure you choose one compatible with the type of paint you used. Turning Dated “Befores” into Stylish “Afters”, Last Updated: April 11, 2020 By Kris Jarrett. Years ago, a professional painter gave me tips on how to paint a door, including the order for painting paneled interior doors and the results are so much better than when I used to just paint a door from the top to the bottom. Thank you!! Trowel concrete resurfacer over your worn walkway, and you'll have a brand new, durable surface with uniform color. The mister is the painter in our family. The doors open into the bathroom, however when closed the one is part of the bedroom and the other part of the hallway. I’ve also experimented with different painting tools and methods over the years and figured out what works best so today I’m sharing my how-to for painting interior doors like a pro!

3. Sand remember to wipe very well, and when you think you have it all do one last time.

Other supplies for this project, including foam rollers and a synthetic angled sash brush, are sold at home centers and paint supply stores.

Many people have success painting doors using just a brush, but I like to use a combination of a brush and a small roller because it gets the job done faster and results in a much smoother finish. 2. Once your second side is dry, simply rehang your doors and reinstall your door hardware. How to Paint Plastic Trim on Doors.

This site uses Akismet to reduce spam. I love the colors. Hi I am repainting the doors and With same paint color and do you have to have a second coat and do you have to sand after the first coat?

You paint it the color that will show when you have the door open, which, assumingly will be most of the time. I have tried sliding, tearing old sweep but I think it’s glued on. Now it’s time to paint!

Thanks, I am painting over 6 panel doors with a acrylic latex primer plus paint. . Did you use any additives in the paint to help paint flow or slow drying times?

However, humidity also has a lot to do with it. All rights reserved. Have learned to paint doors recently ……….Full Gloss is not a good idea, shows the brush marks & imperfections too easily, Semi Gloss is the best, I didn’t undercoat so the door, using white gloss paint, needed 4 coats, so from now on I will always use an undercoat …………… Undercoat has more Titanium in it & it hides and covers better , Titanium makes it more opaque than normal white top paints , Titanium is an expensive addative so it only has a little used in the manufacture of white top coating paints . For more information, see my full disclosure statement {here}. As long as you get all that old semi-gloss paint off the door first and you have a rough surface to apply the new paint, you should be fine. Great instructions. The paint was manufactured by Benjamin Moore in the color “Black Beauty”. 3. If you still have any tiny gaps, spackle lightly then proceed with prep/paint. Paint adheres well to drywall. One of the important tip is to have a small number of different-sized brushes available. What color do I paint the door edge?

The new paint is peeling off the old doors. I don’t have much patience for the task, but this detailed instruction will be helpful to everyone who has ever had to paint a door. This layer is a good test to make sure your MDF is properly sealed. I Painted my interior doors a dark Gray over the original white. Paint all over the wooden trim around glass insets, but paint in the directions of a grain of the wood. What happened? The guys begin restoration of an 1887 Queen Anne Victorian Cottage. For a standard 6-panel door, this is the order to go in: 1. I am gearing up to repaint all the doors in our house (as my children are now old enough to not beat down a closed door with a toy if either of us parents are trying to claim some privacy). What am I doing wrong?

Lot of people use Kilz, I am not a fan, and use Zinsser. You are working with a new, unprimed door. You need to dry wipe them then clean them very good with some little dawn and water, rinse/dry.

However, I’m finding it difficult not to have roller marks. Expert assistance with this segment was provided by Mauro’s Painting. Thanks!

Let me know if you guys have any questions! Priming is ideally done in the same order (edges first, etc. Next, paint the door panels. At the 2020 Idea House: The Farmhouse in Fairfield County, builder Jerry Effren was mindful of the home’s modern farmhouse aesthetic, while also wanting practical solutions in the home. How To: Paint a Metal Door Metal doors offer great benefits in security and weather resistance, but to keep their surfaces welcoming and rust-free, you have to keep up with the painting. Once you’re done, allow the paint to dry (if you’re using Benjamin Moore Advance note that it has a longer than typical dry time), give your door a quick, very light sanding with with 320 grit sandpaper, remove the sanding residue with a tack cloth, and then apply a second coat of paint.

Finally, paint the two vertical strips on the sides with the 4″ roller. xo,

It’s pretty amazing what a difference a fresh coat of paint makes, especially if you’re changing out the hardware too! Pale Creamy Gold Colour is a great feature wall or as a feature colour, goes well with Navy or Grey or Black. I am about to paint my front door and will follow these directions. Switch to a microfiber paint roller to paint the rest of the door.

You are working with new, pre-primed doors, You are using latex paint on a door that was previously painted with latex paint. Rather than simply painting the door from top to the bottom, you can get the best paint job by painting paneled doors in a certain order. The next step is to prime your doors if needed. Learn how your comment data is processed.

How do you prevent them? If you'd like to use any of my images, please request their use via my Contact page.

Cover your sawhorses with a cloth to prevent the newly painted door from sticking to them (and make sure that the cloth you use is smooth with no texture to it, or you could end up with a textured pattern in your door once it comes of the sawhorses). If your door already has knobs on it, I recommend removing them – it’s easier than painting around them.



I’ve noticed some of the paint scratching off mostly around the door knob. I’m painting a 2 panel door and using a roller.

However, if the door is a composite one, you'll need to incorporate a couple of extra procedures or you may have problems with adhesion. If you plan to stain or paint a composite door frame, you need to know the proper preparation steps and the appropriate application techniques or you may end up with a messy, disappointing result. If you want to leave the knobs on, cover your knobs and your hinges with painter’s tape.

Especially if you want to show off black furniture or brass or royal blue & white vase decorations. Hi, I am painting my bathroom trim and 6 panel doors, white on the inside. The oil paint will not damage the fiberglass door but it is more difficult to use. Can be a couple of things. To minimize stroke marks, use long strokes and light pressure on the roller.

InSinkErator’s sleek and efficient products are a perfect fit.